Shears

At home on intricate curves on flat or corrugated metal, one hand is all it takes to make perfect cuts every time. The variable speed, 90 PSI, pneumatic motor, cuts up to 2500 RPM. It will cut 18 gauge mild steel and most grades of stainless to 20 gauge at 40" per minute. It can make tight curves up to 5/8" raduis.

Profile Shear with right hand blades. Cuts profile and flat materials up to 18 gauge C.R. mild steel, soft non-ferrous metals like aluminum, copper and brass to .090; spiral duct, wire mesh and many other materials. These snips are extremely light and maneuverable at 5 pounds, the KD-446R can cut tight curves at a radius of three inches. The blades are made of high quality steel, heat treated and precision ground. 

Profile Shear with left hand blades. Cuts profile and flat materials up to 18 gauge, spiral duct, wire mesh and many other materials. These snips are extremely light and maneuverable at 5 pounds, the KD-446L can cut tight curves at a radius of three inches. The blades are made of high quality steel, heat treated and precision ground. 

This high speed pneumatic TurboShear Model TSS1A is specialized for cutting all types of asphalt shingles. A standard gas powered job-site compressor with 50-foot (15.24 m) hose set-up is adequate to power this versatile air tool. Make fast, clean, straight trim cuts along a roof valley, or make square cuts and circles in shingles with equal precision and ease to fit around utility outlets. A wide jaw opening with a beveled lead-in tip accommodates multiple shingle layers and a lateral blade adjustment capability makes this shear easily maneuverable in any life-rated shingle or thickness. A wide lower blade offers exceptional operator control.

This lightweight, variable-speed pistol-grip shear cuts 14 gauge C.R. mild steel and most grades of stainless to 16 gauge. Double-insulated, the 5 AMP KD-440 cuts at over 150 inches per minute, leaving a clean, flat sheet, ready to fabricate. Distortions are absorbed in an easily disposed of waste curl, leaving the sheet cool and free of burn, chips and burrs. The cutting blades are finest high-speed steel, which you can easily replace. 

Kett KIT #342 KD-442 with Carrying Case includes the KD-442 shear, 253-59 motor, 42-20 shear head and the 251-4 metal carrying case. The KD-442 variable speed shear easily cuts through 16 gauge C.R. mild steel and stainless to 18 gauge. The steel shear head has close cutting heavy duty blades that quickly cut through sheet metal, spiral pipe, metal doors and metal studs.

With a powerful 5 amp motor and speeds up to 2500 strokes per minute, the KD-441 quickly cuts through plastics, wire mesh and rubber with a clean scissors action. When cutting thin coated metals, the swiping cut seals edges and is less likely to rust or corrode. Set the speed of these shears to suit your work.

Product Details:

Kett KD-440 14 gauge power shears. This lightweight, pistol-grip shear cuts 14 gauge mild steel and most grades of stainless up to 16 gauge. Double-insulated, the KD-440 cuts at over 150 inches per minute, leaving a clean, flat sheet, ready to fabricate.

The KD-442 variable speed shear easily cuts through 16 gauge C.R. mild steel and stainless to 18 gauge. The steel shear head has close cutting heavy duty blades that quickly cut through sheet metal, spiral pipe, metal doors and metal studs. Double cutting action provides maximum sheet usage without burring or buckling the material. At less than 5 pounds this KETT shear is both portable for location usage and durable for daily shop operations.

Double-cut shears feed quickly and quietly, without warping or bending the work piece. (Distortion is in the waste strip.) Easily follow a scribed line--edges are not hardened or burred, so you get maximum use of a sheet. Blade swiping action seals the edge of coated metals. Cut sheet metal in straight or contour lines at 180 inches/minute and plastic or formica up to 3/32 in. thick. Includes carrying case.

The P-540 takes over where the P-500 leaves off, cutting up to 14 gauge cold rolled steel, most grades of stainless steel to 20 gauge and aluminum to .090. Its variable-speed trigger lets you make smooth, easy starting cuts even in most grades of stainless up to 16 gauge. The 4 pound, pistol grip, 2200 RPM pneumatic motor, runs on a 90 PSI power source. A great time-saver in any construction company, sheet metal or sign shop.